Copper and PEX repipes done code-correct, permitted, and warrantied
Repiping Services Baton Rouge LA for Homes That Keep Leaking
Our repiping services baton rouge LA crews replace corroded galvanized steel and brittle polybutylene with copper or PEX, usually in two to four days for a typical single-story home. If you are chasing repeat leaks, rusty water, or pressure that drops every time a second fixture runs, the pipe itself is the problem. We pull the permit, cut the walls once, and pressure-test before we close anything up.
Live dispatcherUpfront optionsBacked workmanship
What's included
What Our Repiping Service Includes
A repipe quote should cover the whole job, not just the pipe. Here is what comes standard on our repiping services baton rouge LA projects, and what we handle as an add-on when your home needs it.
Full Supply Line Replacement
We replace every hot and cold supply line from the main shutoff to each fixture, in copper or PEX. That includes the runs behind kitchen and bath walls, the washing machine box, and the water heater connections. No partial repipes that leave old pipe feeding new.
New Shutoff Valves
Every fixture gets a new quarter-turn shutoff valve, so you can isolate a sink or toilet without killing water to the whole house. Old gate valves seize up after 30 years, and this is the moment to replace them while the wall is open.
Permit and Inspection
We pull the plumbing permit through the parish and meet the inspector for the rough-in and final. You get the signed-off paperwork, which matters when you sell the house or file an insurance claim.
Wall Access and Patching
We cut the access points we need, keep them as small as possible, and patch them before we leave. Paint and texture matching is available if you want the walls finished, and we will tell you upfront what that adds.
Pressure Test and Documentation
Before anything gets closed up, we hold the system at test pressure and check every joint. You receive photos of the rough-in and the warranty paperwork at the final walkthrough, so you know what is behind your walls.
Service overview
What Repiping Services Baton Rouge LA Actually Involves
Repiping means removing the old water distribution lines in your home and running new ones from the meter or main through every fixture. We cut into walls and ceilings where needed, sweat new copper pipe or pull PEX tubing through existing chases, and tie in new pipe fittings at every stub-out. A whole home repiping baton rouge Louisiana job covers hot and cold supply lines, shutoff valves, and the connections behind sinks, tubs, toilets, and the water heater.
Most of the homes we open up in East Baton Rouge County were built between 1950 and 1985, and their original galvanized lines are now 40 to 70 years old. Galvanized steel rusts from the inside out, so you get low water pressure, brown water after a vacation, and pinhole leaks behind drywall. Polybutylene, common in late-80s subdivisions, gets brittle and splits at the fittings. If you have typed repiping services near me baton rouge LA into your phone twice this year, that is the sign.
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.
The service timeline
How Our Repiping Process Works
The process flexes to the condition, but these checkpoints keep decisions clear.
Walkthrough and Quote
We walk the house with you, map every fixture, and check the meter, main shutoff, and water heater connections. You get a written price the same day, with the copper and PEX options side by side. No charge for the estimate, and no pressure to sign on the spot.
Permit and Layout
We pull the plumbing permit through the parish and schedule the rough-in inspection. Lines get marked so you know which walls we are opening. If you have a slab-on-grade home, we plan the overhead route through the attic to avoid jackhammering your floors.
Demo and Rough-In
Day one and two are the loud ones. We cut access points, pull the old galvanized or polybutylene, and run new copper pipe or PEX tubing through the attic and walls. Most single-story homes take two to three days of rough-in work, and we clean the work zone every evening.
Fixture Tie-Ins
New shutoff valves go in at every fixture, and we reconnect sinks, tubs, toilets, the washing machine, and the water heater. If your water heater is past 12 years old, that is the cheapest moment to swap it, and we install Rheem, Bradford White, and A.O. Smith units.
Pressure Test and Cleanup
We charge the system and hold it at test pressure to prove every joint. Then the parish inspector signs off, we patch the access points, and you get photos of the rough-in plus the warranty paperwork. Final walkthrough takes about 30 minutes.
Tools & methods
Tools and Methods We Use
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Pipe cutter and soldering torch
Clean, square cuts on copper pipe and properly sweated joints. A ragged cut or a cold joint is where leaks start, so we do not rush this step.
PEX expansion and crimp tools
Correct fittings for PEX tubing, matched to the manufacturer's spec. The right tool for the right connection is what keeps a PEX system leak-free for decades.
Leak detection equipment and pressure gauge
We find hidden leaks before demo and hold test pressure on the new system before anything gets closed up. If it does not hold, we find out while the wall is still open.
Sewer camera and drain snake
While the walls are open, we camera the drain lines and clear any blockage with a snake or auger. It saves a second project later.
RIDGID and Milwaukee power tools
Cutting, drilling, and fastening through studs and joists without over-notching. Proper structural practice matters when you are running pipe through a house frame.
Pipe insulation and Teflon tape
Insulating hot lines cuts heat loss and helps prevent frozen pipes in attic runs. Teflon tape on threaded connections keeps joints sealed.
Use cases
When Baton Rouge Homeowners Call Us to Repipe
These examples show how the service framework adapts rather than forcing every call through one repair.
Slab Leak Repipe in Old Jefferson
A slab-on-grade home had a hot spot on the kitchen floor and a water bill that jumped by $80 in one month. The under-slab copper had corroded through, and the homeowner was facing a jackhammer estimate they did not want. → We confirmed the slab leak with leak detection equipment and routed a new copper repipe through the attic instead. The old line was abandoned in place. The leak stopped, the floor stayed intact, and the water bill dropped back to normal.
Polybutylene Rental Near the LSU Area
A rental property with 1980s polybutylene pipe had a fitting split over a weekend, flooding a bathroom and displacing the tenants for two days. The owner had already repaired two other polybutylene failures that year. → We replaced the entire polybutylene system with PEX in three days, coordinating access with the tenants so they kept water each night. No leaks since, and the owner has permit paperwork and rough-in photos for the file.
Problems we solve
Problems a Repipe Solves for Good
Most repipe calls start with a symptom the homeowner has been living with for years. Here are the ones we hear most in Baton Rouge, and what happens if you keep putting them off.
Pinhole leaks every few months in old copper
We replace the failing runs with new copper or PEX tubing and new pipe fittings, then pressure-test the whole system. One job instead of five service calls, and the wall only gets opened once.
Brown water and low pressure from galvanized pipe
We pull the galvanized steel out and run new lines sized for modern fixtures. Most homeowners see pressure return to normal within a day of the tie-in, and the rust stains in the tub stop.
Polybutylene pipe splitting at the fittings
We replace the entire polybutylene system with PEX or copper, including new fittings at every connection. This is the one material we recommend replacing outright rather than repairing piece by piece.
Slab leak under a slab-on-grade floor
We locate the leak with leak detection equipment, then route the new repipe overhead through the attic. You get new pipe without jackhammering your floors, and the slab stays intact.
Pricing process
What Repiping Costs in Baton Rouge
$4,500 - $12,000 depending on size, material, and access
House size and fixture count
Square footage and the number of sinks, tubs, toilets, and hose bibs drive the pipe footage and the number of tie-ins. A 1,500-square-foot home with two baths is a very different job than a 3,000-square-foot home with four.
Copper versus PEX
Copper costs more on materials and takes longer to install because every joint gets soldered. PEX is faster and cheaper, and it handles freeze-thaw movement better. We quote both so you can weigh cost against lifespan.
Wall and ceiling access
Drywall is quick to open and patch. Plaster, tile, and finished ceilings take more time and care, which adds labor. We plan the smallest possible access points and tell you upfront what patching involves.
How much does repiping a house cost in Baton Rouge LA?
Most whole-home repipes in Baton Rouge run $4,500 to $12,000 in 2026, with the average single-story home landing near $7,500. Square footage, fixture count, and whether we route through the attic or cut the slab drive the number. Copper costs more than PEX on materials. Two-story homes and homes with finished ceilings add labor. We quote both materials in writing so you can compare before you decide.
How long does whole home repiping take in Baton Rouge Louisiana?
A typical single-story Baton Rouge home takes two to four working days from demo to final pressure test. Two-story homes and houses with lots of tile or plaster usually run four to six days. You will have water back at night in most cases, though we may shut it off for a few hours during tie-ins. We schedule the parish inspection as soon as the rough-in is done.
Do I need repiping or just pipe repair in Baton Rouge?
If your home still has galvanized steel or polybutylene and you have had two or more leaks in the past three years, repiping is the better money. A single isolated leak on copper or CPVC pipe is usually worth a repair. We inspect the pipe material and condition first, then tell you straight which one makes sense for your house.
Is PEX repiping better than copper in Baton Rouge LA?
PEX costs roughly 30 to 40 percent less than copper on materials and handles the freeze-thaw swings that burst pipes here in January. Copper lasts longer, holds up to attic heat, and some homeowners simply prefer it. Both meet ICC Plumbing Code when installed correctly. We install both and will tell you which fits your house and budget.
Related services
Related Services
24/7 Emergency Plumber
When a supply line fails at 2 a.m., our on-call crew isolates the leak and stops the water before it spreads. We handle the emergency repair first, then quote the repipe that prevents the next one.
Burst Pipe Repair
Frozen pipes and pressure spikes split copper and CPVC every winter in Baton Rouge. We cut out the failed section, restore water, and flag whether the rest of the run is close behind it.
Water Leak Detection and Repair
We use leak detection equipment and pressure gauges to find hidden leaks behind walls and under slabs. That inspection is often what tells you a repipe is cheaper than chasing leaks one at a time.Ready when you are
Get Your Repiping Services Baton Rouge LA Quote Today
We give same-day estimates, pull the permit, and stand behind the work with a written warranty. If your pipes are leaking, rusting, or losing pressure, call us and we will tell you straight whether you need a repipe or a repair.
Talk with the local team
Request Repiping Services
Call us anytime at +1 866-605-0268 for emergency service. We answer live 24/7 and typically arrive within 60 minutes for urgent calls in Baton Rouge. You can also email us at info@pipedreamrooter&plumbinginc..com for non-emergency inquiries. We're here to help.